HYUNDAI H-SA752 инструкция по эксплуатации онлайн - Страница 2. Hyundai h sa752


HYUNDAI H-SA752 инструкция онлайн просмотр

background image

7

1.Set to the "H.P.F" position when the amplifier is used to drive a tweeter/midrange system. The frequencies below the crossover point will be attenuated at

12dB/octave. Permits adjustment of the crossover frequency ,by rotating the knob to select any frequency between 80Hz to 1.2kHz as the crossover point.

2.Set to the "L.P.F" position when the amplifier is used to drive a subwoofer. The frequencies above the crossover point will be attenuated at 12dB

/octave.Permits adjustment of the crossover frequency, by rotating the knob to select any frequency between 40Hz to 150 Hz as the crossover point.

3.Set to the "OFF" position when the amplifier will be used for driving full-range speakers. The full frequency bandwidth (20Hz - 20,000kHz) will be

output to the speakers without high or low frequency attenuation.

4.Level adjustment-The sensitivity adjustment is to allow the amplifier to work with many different brands of head units. It allows input signal to vary

between 350 millivolts to 5 volt from the head unit or other signal processor. Start by setting the sensitivity adjustment to the "MIN" (3 volts).Using a cassette orcompact disc that you are familiar with ,turn on head unit to the 3/4 volume setting. Slowly turn up sensitivity adjustment towards the "MAX" (200 millivolts)using a flat head screw driver. Stop turning on the onset of distortion and turn back just a slight. The 3/4 volume setting is now the "maximum" volume for thehead unit. The goal is to keep the level control to the lowest setting yet still have enough signal to drive the amplifier. This is done to prevent over driving theamplifier and to keep system noise to a minimum. It is important not over drive speakers (at point of distortion) this will cause permanent damage to thespeakers. Also, if the amplifier itself is over driven, it could be damaged.

5.The "BASS" function can be selected to increase low frequency response output, or decrease frequency response output. The "BASS" function will be

working at only "OFF" or "L.P.F" position. The BASS is adjustable from 0 / 6 / 12dB boost at 50Hz.

Fig.5.

Trouble Shooting Guide

manualbase.ru

HYUNDAI H-SA752 инструкция онлайн просмотр

background image

2

YOUR NEW HIGH FIDELITY BRIDGEABLE/STEREO AMPLIFIER IS DESIGNED TO DELIVER MAXIMUM ENJOYMENT AND ONE YEAR OFTROUBLE FREE SERVICE.

Features

· Four Class ''AB'' High-Current Dual Discrete Drive Stages.

· Class ''AB'' Technology MOSFET PWM Power Supply.

· Bridgeable & TRI-Mode Operation.

· Continuously Variable 12dB/Octave High Pass & 12dB/Octave Low Pass Crossover.

· Subwoofer Variable Crossover for Deep Bass Control.

· Enhanced Bass Boost 0 / 6 / 12dB @ 50Hz.

· Enhanced Treble Boost 0 / 6 / 12dB @ 10kHz

· Gold Plated RCA & Power, Speaker Terminal.

· Soft Start & Muting.· Overload, Thermal, Short Circuit Protection.

· Power & Protection indicator.

Precautions: Read First!

· If after reading the directions you feel uncomfortable about installing the amplifier in your car, or not equipped or competent to do so, you should have

the amplifier installed by an authorized installer. It's your car!

· The negative battery terminal must be disconnected before any electrical connections are made.

· Be sure to choose a location that provides substantial ventilation for the amplifier. The most preferred locations would be in your car's trunk, under the

front seats or on the back wall of a truck.

· The location chosen should provide at least 2" of clearance above the amplifier for adequate ventilation.

· If the amplifier is to be mounted vertically be sure that it is in a place where adequate air will flow along the length of its heatsink fins for cooling.

· NEVER mount the amplifier up side down, this will cause the heat to rise back into the amplifier causing thermal shutdown or possible permanent

damage.

· NEVER mount the amplifier in a location that is subject to direct sunlight or exposed to moisture.

· Be sure to mount the amplifier to a strong, solid surface which will not give way under the stress of a sudden stop or accident.

· Make sure that the mounting screws will not penetrate the gas tank, brake and fuel lines, wiring or other critical parts of your car when installed.

· NEVER operate the amplifier without the proper power and ground wire 10 gauge minimum.

manualbase.ru

HYUNDAI H-SA752 инструкция онлайн просмотр

background image

8

· Before you consult this listing, make sure the vehicle s electrical system is working properly by verifying that other electrical items (e. g. headlights,

Windows, etc.) still function correctly.

SYMPTOM

PROBABLE CAUSE

SOLUTION

Low or N.C. remote turn-on connections

Check remote turn-on voltage at amp and head unit

Blown fuse

Replace with new fast-blow fuse

Power wires not connected

Check butt splices or solder joints;Check ground and battery connections

No audio

Blown or non-speakers connected

Use VOM or DVM to measure speaker coil impedance; check speakerwiring connections

Input sensitivity not set properly or damagedspeaker cones

See adjustment procedure and check each ste; inspect each speaker fordamage and repair or replace suspected component

Distorted audio

Low turn-on voltage

Refer to head unit owner s manual

Audio level low 

Mute circuits is on head unit

Check electrical system for low voltage;Check ground connection

Audio lacks

Speakers wired with wrong polarity, causingcancellation of bass frequencies

Check polarity of wires from amplifiers to each speak as defined bythe system design;Check battery voltage at amplifier during operation

External fuse blowing  Incorrect wiring or short circuit

Refer to electrical installation and check each installation step

Whining noise on audio

with engine running

Amplifier is picking up alternator noise

Install a line noise filter on the head unit s power wire;Check alternator routing diodes or voltage regulator for properoperation. Check all grounds, check battery voltage, check RCAcables

Ticking noise on audio

with engine running

Amplifier is peaking up radiated spark noise

Check RCA audio cable; Install an in-line noise filter on the headunit s power wire, check spark plug wires

manualbase.ru

HYUNDAI H-SA752 инструкция онлайн просмотр

background image

3

· NEVER operate the amplifier without proper fusing. Fuse holder must be located with in 0.5 meters from the battery. This fuse is to protect the car not

the electronics. In case of a short, the fuse will blow instead of the wire burning up. Using other than the recommended fuse ratings at the battery and atthe amplifier may cause damage to the amplifier and will void your warranty.

· Do not run wiring underneath or outside the car since exposure to the elements may cause the insulation to deteriorate rapidly, resulting in short-circuits

and/or intermittent operation.

· All cables should be run beneath carpets and inside trim pieces.

· To help minimize interference, it is best to run the power cables along the opposite side of the audio(RCA) cables.

· Whenever wires pass through metal, rubber or plastic grommets must be used to prevent the metal from wearing through the installation and causing a

short.

· Whenever possible, use cable ties, mounting clamps and similar wiring aids. (available from an electrical supply or auto parts store) Adding stress relief

loops to wiring is also advisable to prevent straining or breakage.

· It is best to test the system before the amplifier is mounted and interior of car is reassembled.

· If the temperature inside your car reaches extreme levels(such as by sitting locked up for several hours in the hot sun or exposed to a very cold winter's

day)the amplifier may go into protection mode and shut off. Leave the unit off until the ambient temperature returns to normal.

· The amplifier operates with any vehicle using a 12 volt negative ground system. If you are not sure of the type of electrical system in your vehicle,

consult your authorized dealer or qualified mechanic.

· NEVER ground the speaker leads and NEVER allow the speaker leads to come in contact with each other. The Speaker wire should be at least 16 gauge

or lower.

· Remote turn on wire must be switched by the radio. If the radio does not have a remote turn on or antenna output, connect to wire that has a positive 12

volts output when the key is turned to the accessory position. If the amplifier does not turn off the battery will die.

· Do not listen to high volumes for extended periods of time or hearing damage may occur.

CONTINOUS EXPOSURE TO SOUND PRESSURE LEVELS OVER 100dBMAY CAUSE PERMANENT HEARING LOSS. HIGH POWERED AUTOSOUNDSYSTEM MAY PRODUCE SOUND PRESSURE LEVELS WELL OVER130dB. USE COMMON SENSE AND PRACTICE SAFE SOUND.

Installation

MOUNTING:1. After reading precaution, decide where you are going to install the unit. Also, see Fig.1.2. Once the location has been determined, place the amplifier into position. Using a felt tip pen or pencil mark the four holes to be drilled for mounting. NEVERuse the amplifier as a template for drilling. It is very easy to damage the amplifier surface in this manner.3. Remove amplifier. Drill four 3.5 mm holes into mounting surface. If you want to mount the amplifier to MDF or wood panel, drill four 3.0m/m diameter holesinto mounting surface.4. If possible, test the system to ensure it is operating correctly before final mounting of the amplifier.

manualbase.ru

HYUNDAI H-SA752 инструкция онлайн просмотр

background image

5

It is important to have good quality power and ground connections. Remember, to complete an electrical circuit, the ground connection is just as important

as the positive power connection. Before any power connections are made, disconnect the ground cable at the battery.

When the power supply lead, memory backup lead or ground lead are extended use a 5mm

2

 (AWG5) or larger automotive grade cable which will withstand

friction and heat to safe grade against fires occurring as a result of short-circuiting.

GND = Connect the proper gauge ground wire to the amplifier "GND" terminal. Locate the position on the chassis of the car to which the amplifier is to be

grounded. The surface must be free from any paint or dirt. This can be accomplished with a small grinding bit, sand paper or wire wheel. NOTE: Do not groundthe amplifier to the "frame of the car. The frame on most cars and trucks is not grounded to the chassis(body). Use Solder or a clamp ring to connect the groundwire. Pre-drill the prepped chassis to bolt the ground ring terminal with nut, bolt and lock washers. Insulate metal and connector with paint or silicon to preventrust and oxidation. Silicon also works great to prevent nuts and bolts from working loose in a harsh environment of an automobile. Upon completion of theground connection, grab wire or connector and confirm that it is a solid connection. To prevent engine noise, it is recommended to ground the head unit and otheraudio electronics in the same location.

REM = Connect the remote wire (power antenna output) from the head unit to the remote turn-on wire of the amplifier. If the head unit is not equipped

with a remote/antenna output, locate a wire that is controlled by the accessory position of the key. It is important to have the amplifier turn off with the radio orkey. If the amplifier remains on, the result will most likely be a dead battery.

12V = Connect the proper gauge power wire to the amplifier "B+" terminal. Run wire to wards the fuse holder that is no greater then 0.5 meters from the

battery. Remember, the fuse is to protect the safety of the car in the case of a short. Connect fuse holder to battery, but do not install fuse at this time.

Fig.3.

SPEAKER CONNECTIONS

manualbase.ru


Смотрите также