HYUNDAI H-SWE3-100 V-UI 304 Amazon инструкция по эксплуатации онлайн - Страница 12. Hyundai h swe3 100v ui304


HYUNDAI H-SWE3-100 V-UI 304 Amazon инструкция онлайн просмотр

background image

8.

Electrical storage water heater

EN

2. WATER HEATER SAFE OPERATION AND INSTALLA-

TION RULES 

Always observe the safety rules, when using the water heater. Improper operation due to igno-rance of these rules may result in personal injury to the user or other people, as well as damage to their property. The manufacturer is not responsible for inflicted personal injuries and property damages as a result of improper installation and operation of the appliance.

Safety of children and people with physical disability

• The water heater is not designed for use by people (including children) with physical, sensory, 

or mental disability having insufficient experience and knowledge, if they are not supervised or instructed on use of the appliance by a person responsible for their safety.

• Any electrical appliance shall be supervised during its operation, especially if there are chil-

dren close by.

• Carefully watch that children do not touch the appliance or use it as a game element.• Do not allow children to use the water heater without supervision by adults.

General safety rules

• Never change the design of the water heater or modify it.• Never use the water heater, if it is faulty.• Do not use the water heater in explosive or corrosive environment. Do not store gasoline and 

other volatile highly inflammable liquids near the appliance.

• Do not use the water heater for purposes not specified in this instruction manual.• Never splash water onto the heater or irrigate it.• Any service operations shall be performed by a specialized organization, by qualified                  

specialists.

Installation/connection safety and precautions

• Installation of the water heater in the operation place and arrangement of a power supply 

line shall be performed by a specialized organization, representatives of the manufacturer’s service department, or specialists having permits for installation of electrical equipment with observation of the safety requirements.

• If the water heater installation/operation instructions are violated, the appliance is not sub-

ject to warranty service and the manufacturer does not bear the responsibility.

• Never install the water heater outdoors.• Before installation and connection of the water heater to the electrical mains, check and 

make sure that the mains socket for the water heater has a grounding contact and it is prop-erly grounded. If there is no grounding loop in your electrical mains, operation of the water heater is hazardous for life.

• Connect the water heater to 220 VAC / 50 Hz mains only. If necessary, clarify specifications of 

your electrical mains from the electrical energy suppliers.

• To avoid overheating and risk of fire / damage of the internal electrical circuit, do not change 

length of the power cord and do not connect the water heater via electrical extension cables.

• Make sure that the electrical cable does not cross sharp edges or contact with hot surfaces.• To avoid air pockets and breakdown of the appliance, the water heater shall be installed 

strictly in vertical position with its connections downward.

• Do not swap locations of the water inlet and outlet positions, since this will result in break-

down of the water heater and may inflict harm to the user (see color marks - blue for water inlet and red for water outlet).

manualbase.ru

HYUNDAI H-SWE3-100V-UI304 инструкция онлайн просмотр

background image

10.

Electrical storage water heater

EN

The electrical water heater shall be installed on a firm wall.The wall planned for installation of the electrical water heater shall be capable to bear at least double weight of the water heater fully filled with water. The wall shall be free of cracks and other damages. Otherwise, take measures to reinforce the mount or install the water heater on a special support.If the bathroom is too small, the water heater can be installed in another place not exposed to direct sunlight and inaccessible for moisture ingress. However for reduction of heat loss in pipes, the installation place of the water heater shall be located as close as possible to the hot water consumption point.When selecting a location for the water heater, ensure free access to it as follows: at least 60 cm between the bottom part of the water heater and floor; at least 10 cm between the top part and ceiling. This will ensure the maximum comfort for maintenance and adjustment of the water heater, when necessary.After you have selected the proper place for installation of the water heater, mark points to make holes for the anchor bolts with hooks. Drill two holes of appropriate depth in the wall using a drill with suitable size for the anchor bolts provided in the water heater package.After that, insert the bolts to the drilled holes and rotate the hooks of the bolts clockwise to securely tighten the nuts of the bolts. Then, hang the water heater onto the hooks of the anchor bolts and check security of mounting.

Mounting

Water supply network connection

The water heater is connected to the cold water supply network with operating pressure from 0.1 MPa to 0.7 MPa. If water pressure in the water supply network exceeds 0.75 MPa, install a reduction valve (pressure reducer) in the feed system so that operating pressure does not exceed 0.75 MPa.If water hardness in the water supply main exceeds 450 mg/l (CaCO3), we recommend you to use a separate water filter upstream of the water heater inlet to extend service life of the heating element.For connection to the water supply network, the water heater has inlet and outlet connectors, which are marked with indication labels and provided with male thread 12 mm in diameter (G1/2”).Install the combined check valve / pressure safety valve provided in the package onto the cold water inlet connection marked with blue color. Connect a drain tube to the pressure relief port of the pressure safety valve for water drainage to the sewers (possible upon heating).

CAUTION! 

Never operate the water heater without the installed check  valve / pressure safety valve.

To facilitate maintenance of the water heater, we recommend you to install a drain valve and a tee between the cold water inlet connection and pressure safety valve. This tee will help you to faster drain water from the water heater. For your convenience, we recommend you to connect a water drain hose to the shutoff valve of the tee. This hose will allow you to route water drained from the water heater to the sewers or another selected destination. Connect the desired quantity of consumption points to the hot water outlet connection marked with red color. Open 

manualbase.ru

HYUNDAI H-SWE3-100V-UI304 инструкция онлайн просмотр

background image

12.

Electrical storage water heater

EN

CAUTION!

During heating, water may begin to drip from the port of the pressure safety valve. Water leakage cannot be avoided and shall not be prevented, since blocking of the valve may result in rupture of the internal tank (in case of equipment breakdown).

4. OPERATION

CAUTION!

Refer to «Water heater safe operation and installation rules»

1 – Power supply indicator2 – Heating indicator3 – Heating capacity regulation 4 – Thermostat knob

Open one of the demountable valves at outlet from the water heater and open the cold water inlet valve. When water starts to freely flow out from the demountable valve, close it and insert the plug of the power cord to the socket. When the water heater is used, the cold water inlet valve shall be in open position. Power supply indicator lights up.  Choose necessary heating capacity using switches situated at the cover. Right switch actuateslow capacity (800 W), left switch actuates middle capacity (1200 W), two switches together actuate high heating capacity (2000 W). - «     » - low capacity (800W), - «     » - middle capacity (1200W),  - «     » - high capacity (2000W). The water heating temperature in the water heater can be set in the range from +35°C to +75°C. To increase the water heating temperature, rotate the thermostat knob clockwise. To decrease the water heating temperature, rotate the thermostat knob counter-clockwise. The water heater automatically maintains the set water temperature. When water temperature in the water heater reaches the user set value, heating will be automatically stopped and the heating indicator will extinguish. When water temperature in the water heater decreases below the user set value, heating will be automatically activated and the heating indicator will light up with bright pink color.

1

2

3

4

manualbase.ru

HYUNDAI H-SWE3-100 V-UI 304 Amazon инструкция онлайн просмотр

background image

10.

Electrical storage water heater

EN

The electrical water heater shall be installed on a firm wall.The wall planned for installation of the electrical water heater shall be capable to bear at least double weight of the water heater fully filled with water. The wall shall be free of cracks and other damages. Otherwise, take measures to reinforce the mount or install the water heater on a special support.If the bathroom is too small, the water heater can be installed in another place not exposed to direct sunlight and inaccessible for moisture ingress. However for reduction of heat loss in pipes, the installation place of the water heater shall be located as close as possible to the hot water consumption point.When selecting a location for the water heater, ensure free access to it as follows: at least 60 cm between the bottom part of the water heater and floor; at least 10 cm between the top part and ceiling. This will ensure the maximum comfort for maintenance and adjustment of the water heater, when necessary.After you have selected the proper place for installation of the water heater, mark points to make holes for the anchor bolts with hooks. Drill two holes of appropriate depth in the wall using a drill with suitable size for the anchor bolts provided in the water heater package.After that, insert the bolts to the drilled holes and rotate the hooks of the bolts clockwise to securely tighten the nuts of the bolts. Then, hang the water heater onto the hooks of the anchor bolts and check security of mounting.

Mounting

Water supply network connection

The water heater is connected to the cold water supply network with operating pressure from 0.1 MPa to 0.7 MPa. If water pressure in the water supply network exceeds 0.75 MPa, install a reduction valve (pressure reducer) in the feed system so that operating pressure does not exceed 0.75 MPa.If water hardness in the water supply main exceeds 450 mg/l (CaCO3), we recommend you to use a separate water filter upstream of the water heater inlet to extend service life of the heating element.For connection to the water supply network, the water heater has inlet and outlet connectors, which are marked with indication labels and provided with male thread 12 mm in diameter (G1/2”).Install the combined check valve / pressure safety valve provided in the package onto the cold water inlet connection marked with blue color. Connect a drain tube to the pressure relief port of the pressure safety valve for water drainage to the sewers (possible upon heating).

CAUTION! 

Never operate the water heater without the installed check  valve / pressure safety valve.

To facilitate maintenance of the water heater, we recommend you to install a drain valve and a tee between the cold water inlet connection and pressure safety valve. This tee will help you to faster drain water from the water heater. For your convenience, we recommend you to connect a water drain hose to the shutoff valve of the tee. This hose will allow you to route water drained from the water heater to the sewers or another selected destination. Connect the desired quantity of consumption points to the hot water outlet connection marked with red color. Open 

manualbase.ru

HYUNDAI H-SWE3-100 V-UI 304 Amazon инструкция онлайн просмотр

background image

12.

Electrical storage water heater

EN

CAUTION!

During heating, water may begin to drip from the port of the pressure safety valve. Water leakage cannot be avoided and shall not be prevented, since blocking of the valve may result in rupture of the internal tank (in case of equipment breakdown).

4. OPERATION

CAUTION!

Refer to «Water heater safe operation and installation rules»

1 – Power supply indicator2 – Heating indicator3 – Heating capacity regulation 4 – Thermostat knob

Open one of the demountable valves at outlet from the water heater and open the cold water inlet valve. When water starts to freely flow out from the demountable valve, close it and insert the plug of the power cord to the socket. When the water heater is used, the cold water inlet valve shall be in open position. Power supply indicator lights up.  Choose necessary heating capacity using switches situated at the cover. Right switch actuateslow capacity (800 W), left switch actuates middle capacity (1200 W), two switches together actuate high heating capacity (2000 W). - «     » - low capacity (800W), - «     » - middle capacity (1200W),  - «     » - high capacity (2000W). The water heating temperature in the water heater can be set in the range from +35°C to +75°C. To increase the water heating temperature, rotate the thermostat knob clockwise. To decrease the water heating temperature, rotate the thermostat knob counter-clockwise. The water heater automatically maintains the set water temperature. When water temperature in the water heater reaches the user set value, heating will be automatically stopped and the heating indicator will extinguish. When water temperature in the water heater decreases below the user set value, heating will be automatically activated and the heating indicator will light up with bright pink color.

1

2

3

4

manualbase.ru

HYUNDAI H-SWE3-100 V-UI 304 Amazon инструкция онлайн просмотр

background image

11.

Electrical storage water heater

EN

1

48

5

6

7

2

3

CAUTION!

Proper grounding is important for minimization of electrical shockand fire hazards.

1 - Inlet connection2 - Outlet connection3 - Tee*4 - Shutoff valve*5 - Pressure safety valve6 - Drain tube*7 - Cold water inlet shutoff valve*8 - Drain hose*

* not included to the package.

the cold water feed valve and one of the demountable valves in order to pass water flow through the water heater and make sure that it is operable. After the tank has been filled as indicated by water flowing from the demountable valve, close it, check tightness of all connections, and retighten them as necessary.

Electrical mains connection

The power cord of the water heater has a plug with a grounding contact. The water heater shall be used with the properly grounded mains socket. If the socket planned for use is not properly grounded or protected with a time-delay fuse / circuit breaker, please contact a qualified electri-cian for replacement of the socket.

The water heater is designed for connection to the electrical mains with single-phase voltage of 220V. Before connection, make sure that parameters of the electrical mains at the connection point meet the parameters indicated on the name plate with specifications of the appliance. During installation of the water heater, observe the effective electrical safety rules. The electrical socket shall be designed for rated current not less than 10A. The electrical cable shall have conductor area not less than 3x1.5 mm2 (for copper).

manualbase.ru

HYUNDAI H-SWE3-100 V-UI 304 Amazon инструкция онлайн просмотр

background image

13.

Electrical storage water heater

EN

5. MAINTENANCE

CAUTION!

Refer to «Water heater safe operation and installation rules»

Check the electrical plug and socket as often as possible. Secure electrical contact and proper grounding shall be assured. The plug and socket shall not heat up abnormally.If the water heater is not used for a long period, especially in regions with low ambient tempera-tures (below 0°C), water shall be drained from the water heater in order to prevent its damage (due to water freezing in the internal tank).To ensure reliable operation of the water heater for a long time, periodically clean the internal tank and remove deposits from the electrical heating elements of the water heater. In addition, periodically check condition of the magnesium anode (whether it is fully dissolved or not) for its timely replacement with a new one in case of full dissolution. The tank cleaning frequency depends on local water hardness.

CAUTION!

The manufacturer provides an extended warranty, when preventive main-tenance operations are carried out (refer to the warranty card).

Cleaning shall be carried out by specialized service departments. The address of the nearest service center can be obtained from the vendor or at www.hyundai-hvac.com. Preventive mainte-nance operations shall be carried out with strict observation of the instruction manual and safety rules.The water heater is equipped with a thermal switch, which will cut off supply of electrical energy to the electrical heating element in the event of water overheating/absence in the water heater. If the water heater is switched on, but water is not heated, this means tripping or need for reset of the thermal switch. To return the water heater to the operational condition, proceed as follows:- disconnect the water heater from power supply and remove the molding of the bottom cover;- press the button at the center of the thermal switch until the button clicks;- if the button is not pressed and there is no click, wait until the thermal switch cools down to the initial temperature.

manualbase.ru


Смотрите также